Upgrade from 1.5.1 or 1.5.2 to 1.5.3 (ECS)

You can upgrade your existing CDP Private Cloud Data Services 1.5.1 or 1.5.2 to 1.5.3 without performing an uninstall.

Review the Software Support Matrix for ECS.
The Docker registry that is configured with the cluster must remain the same during the upgrade process. If CDP Private Cloud Data Services 1.5.1 or 1.5.2 was installed using the public Docker registry, CDP Private Cloud Data Services 1.5.3 should also use the public Docker registry, and not be configured to use the embedded Docker registry. If you would like to use a different configuration for the Docker registry, you must perform a new installation of CDP Private Cloud Data Services.

In Cloudera Manager, navigate to CDP Private Cloud Data Services and click the icon, then click Update.
On the Getting Started page, you can select the Install method - Air Gapped or Internet and proceed.

Internet install method

Air Gapped install method

Click Continue.
On the Collect Information page, click Continue.
On the Install Parcels page, click Continue.
On the Update Progress page, you can see the progress of your upgrade. Click Continue after the upgrade is complete .
note
The upgrade might occasionally fail with error messages or conditions such as the following:

Error message: During the following step: Execute command Install Tolerations Webhook on service ECS-3 the Upgrade progress page mentions a failure waiting for kube-proxy to come up.
Workaround:

Log in using ssh to one of the ECS Server nodes and run the following command:
/var/lib/rancher/rke2/bin/kubectl get nodes
The output will look similar to the following:
NAME STATUS ROLES AGE VERSION ecs-abc-1.vpc.myco.com Ready control-plane,etcd,master 4h50m v1.21.8+rke2r2 ecs-abc-2.vpc.myco.com NotReady <none> 4h48m v1.20.8+rke2r1 ecs-abc-3.vpc.myco.com Ready <none> 4h48m v1.21.8+rke2r2 ecs-abc-4.vpc.myco.com NotReady <none> 4h48m v1.20.8+rke2r1 ecs-abc-5.vpc.myco.com NotReady <none> 4h48m v1.20.8+rke2r1
If any of the version numbers in the last column are lower than the expected version, reboot those nodes. (For example, v1.20.8 in the output above.)

In the Command Output window, in the step that failed, click Resume.

Upgrade hangs on the Execute command Post upgrade configuration on service ECS step for more than an hour.
Workaround:

Log in to one of the ECS server nodes and run the following command:
kubectl get nodes
The output looks similar to the following:
NAME STATUS ROLES AGE VERSION ecs-abc-1.vpc.myco.com Ready control-plane,etcd,master 3h47m v1.21.11+rke2r1 ecs-abc-2.vpc.myco.com NotReady <none> 3h45m v1.21.8+rke2r2 ecs-abc-3.vpc.myco.com NotReady <none> 3h45m v1.21.8+rke2r2 ecs-abc-4.vpc.myco.com NotReady <none> 3h45m v1.21.8+rke2r2
If you any nodes display a status of NotReady, click the Abort button in the command output window.

Reboot all nodes showing NotReady.

Check the node status again as shown above. After all the nodes show Ready, click the Resume button in the command output window to continue with the upgrade.
After the upgrade is complete, the Summary page appears. You can now Launch CDP Private Cloud from here.

If you see a Longhorn Health Test message about a degraded Longhorn volume, wait for the cluster repair to complete.

Or you can navigate to the CDP Private Cloud Data Services page and click Open CDP Private Cloud Data Services.

CDP Private Cloud Data Services opens up in a new window.

If the upgrade stalls, do the following:
1. Check the status of all pods by running the following command on the ECS server node:
```
kubectl get pods --all-namespaces 
```
2. If there are any pods stuck in “Terminating” state, then force terminate the pod using the following command:
```
kubectl delete pods <NAME OF THE POD> -n <NAMESPACE> --grace-period=0 —force 
```
  If the upgrade still does not resume, continue with the remaining steps.
3. In the Cloudera Manager Admin Console, go to the ECS service and click Web UI > Storage UI.
  The Longhorn dashboard opens.
4. Check the "in Progress" section of the dashboard to see whether there are any volumes stuck in the attaching/detaching state in. If a volume is that state, reboot its host.

You may see the following error message during the Upgrade Cluster > Reapplying all settings > kubectl-patch :
```
kubectl rollout status deployment/rke2-ingress-nginx-controller -n kube-system --timeout=5m
error: timed out waiting for the condition
```
If you see this error, do the following:
1. Check whether all the Kubernetes nodes are ready for scheduling. Run the following command from the ECS Server node:
```
kubectl get nodes
```
  You will see output similar to the following:
```
NAME STATUS ROLES AGE VERSION
<node1> Ready,SchedulingDisabled control-plane,etcd,master 103m v1.21.11+rke2r1
<node2> Ready <none> 101m v1.21.11+rke2r1
<node3> Ready <none> 101m v1.21.11+rke2r1
<node4> Ready <none> 101m v1.21.11+rke2r1
```
2. Run the following command from the ECS Server node for the node showing a status of SchedulingDisabled:
```
kubectl uncordon 
```
  You will see output similar to the following:
```
<node1>node/<node1> uncordoned
```
3. Scale down and scale up the rke2-ingress-nginx-controller pod by running the following command on the ECS Server node:
```
kubectl delete pod  rke2-ingress-nginx-controller-<pod number> -n kube-system
```
4. Resume the upgrade.

After upgrading, the Cloudera Manager admin role may be missing the Host Administrators privilege in an upgraded cluster. The cluster administrator should run the following command to manually add this privilege to the role.
```
ipa role-add-privilege <cmadminrole> --privileges="Host Administrators"
```
If you specified a custom certificate, select the ECS cluster in Cloudera Manager, then select Actions > Update Ingress Controller. This command copies the cert.pem and key.pem files from the Cloudera Manager server host to the ECS Management Console host.
After upgrading, you can enable the unified time zone feature to synchronize the ECS cluster time zone with the Cloudera Manager Base time zone. When upgrading from earlier versions of CDP Private Cloud Data Services to 1.5.2+, unified time zone is disabled by default to avoid affecting timestamp-sensitive logic. For more information, see ECS unified time zone.